Products

Water play structure

SKU: L734000386 Category:
SKU: L734000386 Category:

The most important information

:
;

Age group ?2+
Areas of use ?Public playgrounds
Number of users ?15 people
Activities ?Manual activity

Technical data

:
;

Minimum space length ?10.82 m
Minimum space width ?7,44 m
Minimum space height ?1,92 m
Equipment length ?7,82 m
Equipment width ?4,44 m
Equipment height ?1,92 m
Free-fall height ?0,40 m
Platform heights-
Total weight ?710.00 kg
Heaviest single part ?96.00 kg

Assembly & Foundations

:
;

Assembly time ?10,0 h
Number of fitters ?2 people
Lifting equipment required-
FoundationsQuantity: 8 (0.4m x 0.4m x 0.4m)
Quantity: 5 (0.5m x 0.5m x 0.5m)
Quantity: 1 (0.7m x 0.5m x 0.5m)

Product description

:
;

Technical data
Floor area: 4.44 x 7.82 m
Impact area: 7.44 x 10.82 m
Total height: 1.92 m
Free-fall height: 0.40 m
Platform height: 0.40 m

Support post
Standing posts made of robinia plywood, cylindrically milled, Ø 120 mm. Unprotected end grain surfaces are covered with non-detachable stainless steel post caps.
Stainless steel tubular base for the foundation and elevation of Robinia roundwood posts, Ø 120 mm, below the play level.

Platform floor
Platform floor made of 30 mm thick boards and 45 x 100 mm squared timber joists all round. The dried sawn timber made of robinia is planed, bevelled and free of rotting knots. Force-fit floor fastening using special stainless steel brackets with a continuous bolt connection. Pump platform also with profiled stainless steel sheet.

Attachments
- Railing bracket, anti-roll, made of stainless steel tube, Ø 33.7 x 2 mm
- Pouring tube wall made of HPL laminate with sand pouring tube including shut-off damper, fastened between stainless steel tubes Ø 33.7 x 2 mm
- Sand pouring pipe with stainless steel hemisphere
– Sand lift with a rubber transport trough and a 4 mm stainless steel chain, designed as a continuous loop
- Step channel with rubber sand wheel with fabric insert
- Awning made of highly weather-resistant HPL laminate 13 mm
- Table made of highly weather-resistant HPL laminate 20 mm

Water pump article no. 0-33130-001
Water pump for direct connection to a water pipe, suction pipe connection 1 ¼ inch (pipe diameter at least ¾ inch)
Welded stainless steel construction, encapsulated pump housing, pump mechanism with roller and plain bearings, upper pump housing with swivel must be removed, e.g. during the frost period. Cover („winterisation plate“) for the remaining pump base is supplied.

Please note:
When connecting the water pump to a pressurised water line, the K&K valve combination (item no. 0-33190-000 or 0-33195-000) is required.
Please also observe the framework data specified in the installation instructions (spacing, diameter of the cables, etc.); these are available on request from K&K or directly as a PDF from our website at www.kaiser-kuehne.com.

If the water supply is intentionally interrupted temporarily (timer or similar), a negative pressure builds up in the pipe system when the pump is operated again, which causes the pump swivel to kick back.
It is therefore essential to prevent the pump swivel arm from being actuated (e.g. by using the pump lock, part number 1040639).

Water channel 1.60 m
Welded stainless steel construction. Sheet thickness: min. 2 mm. Bevelled spout.
Stepless inclination for installation for the required gradient for the inlet and outlet of the water through additional elevation

Y-channel
Y-shaped water channel with one inlet area and two outlets, sheet thickness: min. 2 mm / pipe Ø 38 mm. Stepless inclination for installation for the required gradient for the inlet and outlet of the water through additional elevations.
Water wheel consisting of 12 blades, folded flat at the front and enclosed by side walls. Wheel bearing with roller bearings, sheet thickness 2.5 mm, with support, tube Ø 38 mm, prepared to accommodate the water channel.

Stowage flap, 4 pieces
Storage flap for K&K water channels, freely positionable, stainless steel handle, rubber blade with fabric insert.

Distributing table (0,50)
Welded stainless steel construction with 2 water drain pipes. Rubber cone closure with locking mechanism for complete water drainage. Sheet thickness min. 2 mm/ pipe Ø 38 mm.
Matching ring foundation (15166) for anchoring to the flange ring and moulded stones (15167) for bricking up and levelling height differences or for secure foundation in loose fall protection (sand, fine gravel, etc.) can be supplied at an extra charge.

Whirling table 0.80 x 1.60 m
Welded stainless steel construction with 5 adjustable HPL prisms acting as flow obstructions. Sheet thickness: min. 2 mm; tube diameter: 33.7 mm or 30 mm.

Mixing plate (0,25)
Welded stainless steel construction with 6 water drainage openings. Sheet thickness: min. 2 mm / pipe Ø 38 mm. Anchored to the flange ring.
Matching ring foundation (15165) for anchoring to the flange ring and moulded stones (15170) for bricking up and levelling height differences or for secure foundation in loose fall protection (sand, fine gravel, etc.) can be supplied at an extra charge.

Metal components: Stainless steel.
The robinia wood is treated with a water-repellent, breathable protective coating. In addition to protecting against moisture, this treatment also reduces cracking. The modular add-on parts transfer their forces directly to the uprights via a special adapter fastening. The screw connections are secured against unauthorised loosening by cover caps.

Foundations (client-provided)
8 pcs. 0.40 x 0.40 x 0.40 m
5 pcs. 0.50 x 0.50 x 0.50 m
1 piece 0.50 x 0.70 x 0.50 m

Assembly time
2 fitters, 10 hours each.
(without foundation, without water connection)

Suitable for
Children from 2 years,
public playgrounds etc.,
Manual activities

Item number: L734000386