Posts
Laminated Robinia timber Ø 120 mm with cylindrical milling. End-grain surfaces are covered by non-detachable protective stainless steel caps. Stainless steel tubular pedestal for concrete-cast foundation and for fixed mounting to round Robinia posts, Ø 120 mm, below playing surface.
Platforms
Platforms from boards of 30 mm thickness and all-round square-shaped joists 45 x 100 mm. Dried timber from Robinia, planed, milled and free from decay. Force-fitting fastening through specific stainless steel brackets with end-to-end bolt assembly.
Attachment parts
– tandem guardrails from stainless steel tubes, Ø 33,7 x 2 mm
– bowed guardrails with roll-off prevention, from stainless steel tubes, Ø 33,7 x 2 mm
– entrance guardrail with roll-off prevention, welded assembly from stainless steel tubes Ø 33,7 x 2 mm, consisting of a horizontal guardrail and vertically positioned bent retaining tubes
– stepped handrail made from tubular stainless steel, Ø 33,7 x 2 mm
– timber infill barrier from Robinia, 125 x 30 mm, fastening between stainless steel tubes Ø 33,7 x 2 mm; with additional waling timber, 30 mm, for nominal heights of 1,50 m and more
– infill barriers from stainless steel tubes, Ø 33,7 x 2 / 25 x 2 mm, one-piece welded assembly
– ladder access from tubular stainless steel Ø 38 x 2 mm, height of the first rung: 0,50 m, glas-bead blasted, for additional subsequent platform attachment or for concrete-cast embedding
– cranked ladder rung made from stainless steel tubes Ø 33,7 x 2 mm
– sloping tottery stairs suspended from fine stainless steel chains fixed to tandem guardrails, Robinia round logs Ø 100 mm
– inclined ramp from Robinia timber with a tandem guardrail from stainless steel tubes with a fixed Hercules climbing rope Ø 18 mm
– climb up ramp from highly weather-resistant HPL, 20 mm thickness, stainless steel frame, with five cut-outs for climbing
– climbing rung made from tubular stainless steel, Ø 38 mm, with twist protection
– climbing net from Hercules ropes fixed to a stainless steel frame
– vertical climbing pole made from tubular stainless steel Ø 38 mm
– climbing net from stainless steel chains with RS120 post attachment
– sloped scramble up net fixed to a tubular stainless steel frame Ø 16 mm
– seat made from highly weather-resistant coloured HPL, 20 mm thickness, mounted on top of a stainless steel tube, Ø 33,7 x 2 mm
– sand chute and rubber sand wheel with fabric insert
– sand chute from coloured HPL in a tubular stainless steel frame
– sand pulley with rubber scoop and stainless steel chain, link thickness of 4 mm. Continuous loop construction to block its drawing into adjoining playing areas/free spaces
– double t-shaped transport rail with rubber scoop
– arch-shaped Robinia bridge with tandem handrail from stainless steel
– tottery bridge suspended from tandem crossbeams, Robinia logs Ø 10 cm, suspended from fine stainless steel chains, protection against the possibility of stepping through
– suspension bridge from Robinia joists 45 x 100 mm with rubber buffers 30 mm, stainless steel supporting cable Ø 10 mm with four tensioning devices, fine stainless steel chains
– plank bridge: V-shaped climbing net construction from Hercules ropes, Robinia footbridge with approx. 40 mm clear distance between the planks. Attachment to a steel frame construction, barrier height approx. 0,75 m
– stairs for post attachment made from Robinia 170 x 45 mm, fixed to stainless steel framework Ø 33,7 x 2 mm, step spacing 133 mm
– pair of Robinia infill barriers for the stairs, fastening between stainless steel tubes Ø 33,7 x 2 mm
– helical tunnel slide 30°/’38° from stainless steel, 2,5 mm, of low noise level thanks to tunnel shape, the slide is (in three parts) welded to a centre pylon including appropriate connecting flanges to facilitate installation on site
– hill slide 30°, installation height 2,80 m, sliding sections from stainless steel, of low noise level thanks to trough shape, including a support post for the curved section as well as a fastening flange, respectively made from stainless steel
– trough-shaped attachment slide, width 0,60 m, one-piece welded assembly, sheet metal thickness 2,5 mm, with roll-off prevention above the entrance section
– attachment slide, width 1,10 m, one-piece welded assembly, stainless steel sheet thickness: 2,5 mm, with roll-off prevention above the entrance section
– tower-shaped roof, 80° inclination, from highly weather-resistant coloured HPL, 13 mm thickness, round edges
– stainless steel hood with receptacle for a flag, bent for towers 6 x 80°, 1,5 mm, with pre-assembled flag
– tower-shaped roof, 72° inclination, from highly weather-resistant coloured HPL, 13 mm thickness
– stainless steel hood with receptacle for a flag, bent for towers 6 x 72°, 1,5 mm, with pre-assembled flag
– trapezoid single-pitch roof, 30° inclination, from highly weather-resistant coloured HPL, 13 mm, attachment to a stainless steel frame Ø 33,7 x 2 mm
For your planning, due to a possible sliding surface heating, please see to a north-east orientation of the slides or provide half-shade of trees.
Metal components: stainless steel
Robinia timber is furnished with water-repellent, breathable protective coating. Besides protection from moisture, that treatment reduces crack formation. Thanks to a specific fastening adaptor, forces arising from the modular attachment parts are directly derived into the posts. Tamper-proof screw connections thanks to screws with protective screw cap.