Water Play Structures

Technical data
Total height: 2,91 m
Area: 2,88 x 3,37 m
Minimum space: 5,86 x 6,13 x 2,91 m
Platform height: 0,30 m
Weight: 80 kg heaviest single component
580 kg as a whole

Posts
Laminated Robinia timber Ø 120 mm with cylindrical milling. End-grain surfaces are covered by non-detachable protective stainless steel caps.
Stainless steel tubular pedestal for concrete-cast foundation and for fixed mounting to round Robinia posts, Ø 120 mm, below playing surface.

Platforms
Platforms from boards of 30 mm thickness and all-round square-shaped joists 45 x 100 mm. Dried timber from Robinia, planed, milled and free from decay. Force-fitting fastening through specific stainless steel brackets with end-to-end bolt assembly.
The pump platform is additionally covered by profiled stainless steel sheet.

Attachment parts
– bowed guardrail with roll-off prevention, from stainless steel tubes, Ø 33,7 x 2 mm
– tandem guardrail from stainless steel tubes, Ø 33,7 x 2 mm
– gable roof 45° / 0,80 m x 1,60 m rounded eaves, from highly weather-resistant coloured HPL, 13 mm, fastening to a tubular stainless steel frame Ø 33,7 x 2 mm
– sand pulley with rubber scoop and stainless steel chain, link thickness of 4 mm. Continuous loop construction to block its drawing into adjoining playing areas/free spaces
– sand chute and rubber sand wheel with fabric insert
– infill panel from highly weather-resistant coloured HPL with sand chute and shutter, fastening between stainless steel tubes Ø 33,7 x 2 mm
– sand chute from HPL in a tubular stainless steel frame

Water pump
Suction pipe connection 1 ¼ in (pipe diameter at least ¾ in), welded stainless steel construction, fully encapsulated pump housing, pump mechanism with roller and anti-friction bearing. During winter season, a removal of the upper housing and the handle is indispensable, (winter) cover panel for the bottom part is included with delivery.

Please note:
The installation of the water pump to a pressure water pipe requires a K&K Valve combination (item no. 0-33190-000 or 0-33195-000).
If the water supply to the pump (through a clock timer or similar) is interrupted, the pump handle must be safeguarded against operation (for example by the K&K pump latch, item no. 1040639). This prevents a handle setback due to an increasing negative pressure.
Please also consider the basic technical details given in the installation instructions (such as spacing, pipe diameters etc.); upon request, you will receive them directly from K&K or by downloading the corresponding PDF from www.kaiser-kuehne.com

If the water supply to the pump (through a clock timer or similar) is interrupted, the pump handle must be safeguarded against operation (for example by the K&K pump latch, item no. 1040639). This prevents a handle setback due to an increasing negative pressure.

Water trough 0,80 m
Welded stainless steel construction, sheet metal thickness: min. 2 mm / tube Ø 38 mm. Inclined run-off. With additional trough support for inclined installation corresponding to water feed or water run-off.

Distributing trough
Total height: 1,15 m
Weight: 35 kg as a whole
Welded structure made of stainless steel with adjustable, shock absorbing tilt-mechanism to distribute the waterflow in opposite directions.
Thickness of steel sheet: 2,5 mm/tube Ø 38 mm
with tubular stainless steel support and edge protection Ø 38 x 2 mm

Water table (0,25)
Total height: 0,40 m
Welded structure made of stainless steel with one water outlet and one storage surface. Conical rubber closing with locking mechanism. Sheet metal thickness: 2,5 mm / tube Ø 38 mm.
Anchorage by means of ring-shaped bottom flange. At extra charge, there are appropriate ring-shaped concrete foundations (015165) for flange fastening and concrete form blocks (015170) for masonry works to compensate different levels or for a safe installation with loose fall protection surfacing (sand, gravel etc.).

Mixing plate (0,25)
Welded structure made of stainless steel with six water outlets. Sheet metal thickness: min. 2 mm/ tube Ø 38 mm. Anchorage by means of ring-shaped bottom flange. At extra charge, there are appropriate ring-shaped concrete foundations (015165) for flange fastening and concrete form blocks (015170) for masonry works to compensate different levels or for a safe installation with loose fall protection surfacing (sand, gravel etc.)

Metal components: stainless steel
Robinia timber is furnished with water-repellent, breathable protective coating. Besides protection from moisture, that treatment reduces crack formation. Thanks to a specific fastening adaptor, forces arising from the modular attachment parts are directly derived into the posts. Tamper-proof screw connections thanks to screws with security socket.

Foundations (on site)
6 pcs. 0,40 x 0,40 x 0,40 m
2 pcs. 0,50 x 0,50 x 0,50 m
1 pc. 0,50 x 0,70 x 0,50 m

Approximate assembly values
2 mechanics 8 hours each
(without creating foundations, without water supply connection)

Free height of fall
0,72 m

Appropriate for
children from the age of 4 years up,
public playgrounds etc.,
manual activity