Water Play Structures

Technical data
Area: 4,35 x 7,07 m
Minimum space: 7,35 x 10,07 m (52 m²)
Total height: 2,00 m
Platform height: 0,20/0,95 m
Weight: 55 kg heaviest single component
626 kg as a whole

Posts
Laminated Robinia timber Ø 120 mm with cylindrical milling. End-grain surfaces are covered by non-detachable protective stainless steel caps.
Stainless steel tubular pedestal for concrete-cast foundation and for fixed mounting to round Robinia posts, Ø 120 mm, below play level. Upper ends of posts level with platforms are covered by welded-on circular blanks made from stainless steel.

Platforms
Platform from boards of 30 mm thickness and all-round square-shaped joists 45 x 100 mm. Dried timber from Robinia, planed, milled and free from decay. Force-fitting fastening through specific stainless steel brackets with end-to-end bolt assembly.
The water pump platform is additionally covered by profiled stainless sheet steel.

Attachment parts
– bowed guardrail with roll-off prevention, from stainless steel tube, Ø 33,7 x 2 mm
– tandem guardrail from stainless steel tubes, Ø 33,7 x 2 mm
– timber infill barrier from Robinia, 125 x 30 mm, fastening between stainless steel tubes Ø 33,7 x 2 mm
– cranked ladder rung made from stainless steel tube Ø 33,7 mm
– vertical handle from stainless steel tube Ø 33,7 x 2 mm, as a climbing aid

Water pump
Suction pipe connection 1 ¼ in (pipe diameter at least ¾ in), welded stainless steel construction, fully encapsulated pump housing, pump mechanism with roller and anti-friction bearing. During winter season, a removal of the upper housing and the handle is indispensable, (winter) cover panel for the bottom part is included with delivery.
Please note:
The installation of the water pump to a pressure water pipe requires a K&K Valve combination (item no. 0-33190-000 or 0-33195-000).
If the water supply to the pump (through a clock timer or similar) is interrupted, the pump handle must be safeguarded against operation (for example by the K&K pump latch, item no. 1040639). This prevents a handle setback due to an increasing negative pressure.
Please also consider the basic technical details given in the installation instructions (such as spacing, pipe diameters etc.); upon request, you will receive them directly from K&K or by downloading the corresponding PDF from www.kaiser-kuehne.com.

Y-shaped water trough
Welded stainless steel construction with one water feed and two run-offs, sheet metal thickness: 2 mm at least/ tube Ø 38 mm. Including flexible flap (2 pcs.) with stainless steel knob and reinforced rubber blade, clamping device for tube attachment Ø 38 mm

Water wheel Ø 0,60 m
Welded stainless steel construction, for water collection from a trough on top, 12 paddle wheels, rounded on the front end, framed by side panels. Sheet metal thickness: 2 mm at least. Water wheel mounted in roller bearing. Additional support Ø 38 mm) for trough attachment

Water trough 1,60 m, 3 pcs.
Welded stainless steel construction. Sheet metal thickness: 2 mm at least. Ø 38 mm. Inclined run-off.
Additional trough support for inclined installation corresponding to water feed or water run-off.

Slidable flap, 5 pcs.
with stainless steel knob and reinforced rubber blade. Limited shifting on choice.

Stand-alone bottom water basin for screw pumps
Welded stainless steel construction with discharge drilling, closed by a cylinder screw. Screw connection of the bottom bearing of the screw pump. Sheet metal thickness 2 mm / tube Ø 38 mm.
At extra charge, there are appropriate ring-shaped concrete foundations (015168) for flange fastening and concrete form blocks (015169) for masonry works to compensate different levels or for a safe installation with loose fall protection surfacing (sand, gravel etc.).

Screw pump with hand wheel and revolving disc at the upper end
Length: 2,00 m
Outer diameter: 0,25 m
Hand wheel diameter: 0,80 m
Welded stainless steel construction for post attachment, with roller bearings, base bearing facilitating screw fastening.

Modular collecting basin
Welded stainless steel construction with discharge pipe. Sheet metal thickness 2 mm / tube Ø 38 mm, for post attachment.

Water basin (0,50)
Base area: 0,84 x 1,00 m
Total height: 0,65 m
Weight: 55 kg as a whole
Welded stainless steel construction with one discharge drilling. Sheet metal thickness: min. 2 mm / tube Ø 38 mm. Anchorage by means of ring-shaped bottom flange.
At extra charge, there are appropriate ring-shaped concrete foundations (015165) for flange fastening and concrete form blocks (015170) for masonry works to compensate different levels or for a safe installation with loose fall protection surfacing (sand, gravel etc.)

Water table (0,25)
Total height: 0,40 m
Welded structure made of stainless steel with one water outlet and one storage surface. Conical rubber closing with locking mechanism. Sheet metal thickness: 2 mm at least / tube Ø 38 mm.
Anchorage by means of ring-shaped bottom flange. At extra charge, there are appropriate ring-shaped concrete foundations (015165) for flange fastening and concrete form blocks (015170) for masonry works to compensate different levels or for a safe installation with loose fall protection surfacing (sand, gravel etc.).

Metal components: stainless steel
Robinia timber is furnished with water-repellent, breathable protective coating. Besides protection from moisture, that treatment reduces crack formation. Thanks to a specific fastening adaptor, forces arising from the modular attachment parts are directly derived into the posts. Tamper-proof screw connections thanks to protective screw caps.

Foundations (on site)
9 pcs. 0,40 x 0,40 x 0,40 m
7 pcs. 0,50 x 0,50 x 0,50 m
1 pc. 0,50 x 0,70 x 0,50 m
concrete amount: 1,63 m³

Approximate assembly values
2 mechanics 8 hours each
(without creating foundations, without water supply connection)

Free height of fall
1,20 m

Appropriate for
children from the age of 3 years up,
public playgrounds etc.,
manual activity