Water Play Structures

Technical data
Area: 7,98 x 7,32 m
Total height: 2,30 m
Minimum space: 11,48 x 10,28 x 2,30 m
Platform height: 0,60/0,80 m
Weight: 75 kg heaviest single component
1316 kg as a whole

Posts
Posts made from stainless steel tubes Ø 120 x 3 mm covered by non-detachable protective stainless steel caps. Except for posts level with platforms, end-grain surfaces are covered by non-detachable protective stainless steel caps.

Platforms
Platforms from boards of 30 mm thickness and all-round square-shaped joists 45 x 100 mm. Dried timber from Robinia, planed, milled and free from decay. Force-fitting fastening through specific stainless steel brackets with end-to-end bolt assembly.
The pump platform is additionally covered by profiled stainless steel sheet.

Attachment parts
– stairs for post attachment made from Robinia 170 x 45 mm, fixed to stainless steel framework Ø 33,7 x 2 mm, step spacing 133 mm
– pair of stainless steel infill barriers for stairs, Ø 33,7 x 2 / 20 x 2 mm, one-piece welded assembly
– sand pulley with rubber scoop and stainless steel chain, link thickness of 4 mm. Continuous loop construction to block its drawing into adjoining playing areas/free spaces
– sand funnel without stopper, stainless steel half-shell with welded-on stainless steel ring
– sand chute from coloured HPL in a tubular stainless steel frame
– bowed guardrail with roll-off prevention, from stainless steel tubes, Ø 33,7 x 2 mm
– tandem guardrail 0,80 m/ from stainless steel tubes , Ø 33,7 x 2 m
– ladder rung from stainless steel tubes, Ø 33,7 mm
– entrance guardrail with roll-off prevention, welded assembly from stainless steel tubes Ø 33,7 x 2 mm, consisting of a horizontal guardrail and vertically positioned bent retaining
– stainless steel infill barrier, Ø 33,7 x 2 / 25 x 2 mm, one-piece welded assembly
– trough-shaped attachment slide, width 0,60 m, one-piece welded assembly, stainless steel sheet thickness: 2,5 mm, with roll-off prevention above the entrance section

Water pump with handle
Suction pipe connection 1 ¼ in (pipe diameter at least ¾ in), welded stainless steel construction, fully encapsulated pump housing, pump mechanism with roller and anti-friction bearing. During winter season, a removal of the upper housing and the handle is indispensable, (winter) cover panel for the bottom part is included with delivery. Facilitating fastening to solid ground or e.g. a platform on site.
Please note:
The installation of the water pump to a pressure water pipe requires a K&K Valve combination (item no. 0-33190-000 or 0-33195-000).
If the water supply to the pump (through a clock timer or similar) is interrupted, the pump handle must be safeguarded against operation (for example by the K&K pump latch, item no. 1040639). This prevents a handle setback due to an increasing negative pressure.
Please also consider the basic technical details given in the installation instructions (such as spacing, pipe diameters etc.); upon request, you will receive them directly from K&K or by downloading the corresponding PDF from www.kaiser-kuehne.com.

Water storage basin
Base area: Ø 0,86 m
Welded stainless steel construction with a tubular outlet pipe. Conical rubber closing with locking mechanism for complete water extraction. Sheet metal thickness: 2 mm at least / tube Ø 33,7 mm, post attachment

Y-shaped water trough
Welded stainless steel construction with one water feed and two run-offs, sheet metal thickness: 2 mm at least/ tube Ø 38 mm. Including flexible flap (2 pcs.) with stainless steel knob and reinforced rubber blade, clamping device for tube attachment Ø 38 mm. Limited shifting on choice.

Water swirl table
Welded stainless steel construction with five adjustable triangular HPL plates for water flow obstruction. Sheet metal thickness: 2 mm at least, tube Ø 33,7 mm resp. Ø 30 mm

Water distributing table (0,75)
Total height: 0,90 m
Welded structure made of stainless steel with two water outlets. Conical stopper made of rubber with fixing device for total removal of water. Thickness of sheet steel: min. 2 mm/pipe Ø 38 mm. Anchorage by means of ring-shaped bottom flange. At extra charge, there are appropriate ring-shaped concrete foundations for flange fastening and concrete form blocks for masonry works to compensate different levels or for a safe installation with loose fall protection surfacing (sand, gravel etc.).

Basin with water outlet pipe for terracing installation, post attachment
Base area: Ø 0,90 m
Total height: 0,14 m
Welded stainless steel construction with outlet pipe, sheet metal thickness: 2 mm at least / tube Ø 38 mm

Water trough 0,80 m
Welded stainless steel construction. Sheet metal thickness: 2 mm at least / tube Ø 38 mm, inclined run-off. Designed for inclined installation for water supply and run-off by means of additional tubular support(s).

Water trough 1,60 m
Welded stainless steel construction. Sheet metal thickness: 2 mm at least / tube Ø 38 mm, inclined run-off. Designed for inclined installation for water supply and run-off by means of additional tubular support(s). Including flexible flap with stainless steel knob and reinforced rubber blade, clamping device for tube attachment Ø 38 mm

Stand alone bottom basin for screw pump
Welded stainless steel construction with discharge drilling, closed by a cylinder screw. Screw connection of the bottom bearing of the screw pump. Sheet metal thickness 2 mm at least / tube Ø 38 mm. At extra charge, there are appropriate ring-shaped concrete foundations for flange fastening and concrete form blocks for masonry works to compensate different levels or for a safe installation with loose fall protection surfacing (sand, gravel etc.).

Screw pump (2,00) with hand wheel and revolving disc at the upper end
Length: 2,00 m
Outer diameter: 0,25 m
Hand wheel diameter: 0,80 m
Welded stainless steel construction for post attachment, with roller bearings, base bearing facilitating screw fastening.

Modular collecting basin
Welded stainless steel construction with discharge pipe. Sheet metal thickness 2 mm / tube Ø 38 mm, for post attachment

Water trough 1,60 m for post attachment
Welded stainless steel construction 0,80 m x 1,60 m, Sheet metal thickness: 2 mm at least / tube Ø 38 mm, inclined run-off.
Including flexible flap with stainless steel knob and reinforced rubber blade, clamping device for tube attachment Ø 38 mm

Water wheel for post attachment
Wheel diameter: Ø 0,60 m
Welded stainless steel construction for post attachment, for water collection from a trough on top, 12 paddle wheels, rounded on the front end, framed by side panels. Sheet metal thickness: 2 mm at least. Water wheel mounted in roller bearing.

Metal components: stainless steel
Robinia timber is furnished with water-repellent, breathable protective coating. Besides protection from moisture, that treatment reduces crack formation. Thanks to a specific fastening adaptor, forces arising from the modular attachment parts are directly derived into the posts. Tamper-proof screw connections thanks to screws with security socket.

Foundations (on site)
29 pcs. 0,40 x 0,40 x 0,40 m
4 pcs. 0,30 x 0,30 x 0,40 m
1 pc. 0,75 x 0,40 x 0,40 m
concrete amount: 2,2 m³

Approximate assembly values
2 mechanics 8 hours each
(without creating foundations, without water supply connection)

Free height of fall
1,00 m

Appropriate for
children from the age of 4 years up,
public playgrounds etc.,
manual activity