Water Play Structures

Technical data
Area: 2,80 x 3,95 m
Minimum space: 6,00 x 6,95 m (34 m²)
Total height: 3,00 m
Platform height: 0,70 m
Free height of fall: 1,20 m
Weight: 105 kg heaviest single component
560 kg as a whole

Posts
Laminated Robinia timber Ø 120 mm with cylindrical milling. End-grain surfaces are covered by non-detachable protective stainless steel caps.
Stainless steel tubular pedestal for concrete-cast foundation and for fixed mounting to round Robinia posts, Ø 120 mm, below playing surface.

Robinia timber is furnished with water-repellent, breathable protective coating. Besides protection from moisture, that treatment reduces crack formation. Thanks to a specific fastening adaptor, forces arising from the modular attachment parts are directly derived into the posts. Tamper-proof screw connections thanks to protective screw caps.

Platform
Platform from boards of 30 mm thickness and all-round square-shaped joists 45 x 100 mm. Dried timber from Robinia, planed, milled and free from decay. Force-fitting fastening through specific stainless steel brackets with end-to-end bolt assembly.

Attachment parts
– bowed guardrail with roll-off prevention, from stainless steel tubes, Ø 33,7 x 2 mm
– cranked ladder rung from stainless steel tube Ø 33,7 x 2 mm
– half a tent roof, 45° inclination, from highly weather-resistant blue HPL panels, 13 mm thickness, fastening to stainless steel frame Ø 33,7 x 2 mm
– timber infill barriers from Robinia, 125 x 30 mm, fastening between stainless steel tubes Ø 33,7 x 2 mm
– stainless steel infill barriers, Ø 33,7 x 2 / 25 x 2 mm, one-piece welded assembly

Stand alone bottom basin for screw pump
Welded stainless steel construction with discharge drilling, closed by a cylinder screw. Screw connection of the bottom bearing of the screw pump. Sheet metal thickness 2 mm / tube Ø 38 mm.
At extra charge, there are appropriate ring-shaped concrete foundations (015168) for flange fastening and concrete form blocks (015169) for masonry works to compensate different levels or for a safe installation with loose fall protection surfacing (sand, gravel etc.).

Collecting basin
Welded stainless steel construction with discharge drilling. Sheet metal thickness 2 mm / tube Ø 38 mm, for post attachment.

Screw pump with hand wheel and crank drive
Length: 2,00 m
Outer diameter: 0,25 m
Hand wheel diameter: 0,80 m
Welded stainless steel construction for post attachment, with roller bearings, base bearing facilitating screw fastening.

Water table (0,50)
Base area: 0,84 x 1,84 m
Total height: 0,65 m
Welded stainless steel construction with one tubular run-off and four storage surfaces. Conical rubber closing with locking mechanism. Sheet metal thickness: 2,5 mm / tube Ø 38 mm.
At extra charge, there are appropriate ring-shaped concrete foundations (015165) for flange fastening and concrete form blocks (015170) for masonry works to compensate different levels or for a safe installation with loose fall protection surfacing (sand, gravel etc.)

Gargoyle
Welded stainless steel construction wiht a clamping device for tube Ø 38 mm, with receptacle for a water hose plug 1/2″ resp. 3/4″. (for instance Gardena® or similar type).

Water trough type M5 1,60 m
Welded stainless steel construction 0,80 m x 1,60 m, Sheet metal thickness: 2 mm / tube Ø 38 mm. For post attachment and with additional trough support for inclined installation corresponding to water feed or water run-off. Inclined run-off, including flexible flap with stainless steel knob and reinforced rubber blade.

Basin with one run-off for terracing installation
Base area: Ø 0,90 m
Total height: 0,14 m
Welded stainless steel construction with discharge drilling. Sheet metal thickness 2 mm / tube Ø 33,7 mm, for post attachment.

Foundations (on site)
8 pcs. 0,40 x 0,40 x 0,40 m
1 pc. 0,50 x 0,50 x 0,50 m
concrete amount: 0,7 m³

Approximate assembly values
2 mechanics 3 hours each
(without creating foundations, without water supply connection)

Appropriate for
children from the age of 2 years up,
public playgrounds etc.,
manual activity