Water Play Structures

Technical data
Total height: 4,80 m
Area: approx. 8,40 x 11,55 m
Minimum space: 11,40 x 14,55 m (116 m²)
Platform heights: 0,20/1,15/1,60/1,80 m
Weight: 140 kg heaviest single component
1885 kg as a whole

Posts
Posts made from stainless steel tubes Ø 120 x 3 mm covered by non-detachable protective stainless steel caps.
Upper ends of posts level with platforms are covered by welded-on circular blanks made from stainless steel.

Platforms
Platforms from boards of 30 mm thickness and all-round square-shaped joists 45 x 100 mm. Dried timber from Robinia, planed, milled and free from decay. Force-fitting fastening through specific stainless steel brackets with end-to-end bolt assembly.
The pump platform is additionally covered with profiled stainless steel sheet and prepared for mounting the valve combination included in this water feature. The valve combination will be located directly below the pump platform. An additional shaft for the valve combination is therefore not required.

Attachment parts
– flat ramp 2,40 m x 1,60 m, 0,10 m slight incline, made from profiled boards 95 x 30 mm
– (cranked) ladder rungs from stainless steel tubes, Ø 33,7 mm
– bowed guardrails with roll-off prevention, from stainless steel tubes, Ø 33,7 x 2 mm
– tandem guardrails 0,80 m/ from stainless steel tubes , Ø 33,7 x 2 mm
– vertical handle from stainless steel tube Ø 33,7 x 2 mm, as a climbing aid
– stainless steel infill barriers, Ø 33,7 x 2 / 25 x 2 mm, one-piece welded assembly
– table 0,80 x 0,80 m, made from a coloured highly weather-resistant HPL panel (15 mm thickness)
– tent roof with whirligig, 6 x 0,80 m / 45° inclination, made from highly weather-resistant coloured HPL panels, 13 mm thickness; fastening to stainless steel frame Ø 33,7 x 2 mm
– sloping tottery stairs 0,80 m x 2,40 m, suspended from tandem railings, rungs from Robinia logs Ø 10 cm, fine stainless steel chains

Water pump item no. 0-33130-001
Suction pipe connection 1 ¼ in (pipe diameter at least ¾ in), welded stainless steel construction, fully encapsulated pump housing, pump mechanism with roller and anti-friction bearing. During winter season, a removal of the upper housing and the handle is indispensable, (winter) cover panel for the bottom part is included with delivery.

Please note:
The installation of the water pump to a pressure water pipe requires a K&K Valve combination (item no. 0-33190-000 or 0-33195-000).
If the water supply to the pump (through a clock timer or similar) is interrupted, the pump handle must be safeguarded against operation (for example by the K&K pump latch, item no. 1040639). This prevents a handle setback due to an increasing negative pressure.
Please also consider the basic technical details given in the installation instructions (such as spacing, pipe diameters etc.); upon request, you will receive them directly from K&K or by downloading the corresponding PDF from www.kaiser-kuehne-play.com.

Valve combination item no. 0-33190-000
Device for direct connection to mains supply, with integrated fine filter for water purification to prevent a malfunction due to polluted membrane filters.
Assembly and installation must be carried out by a qualified company.

Basin with two run-offs for terracing installation
Base area: Ø 0,90 m
Total height: 0,14 m
Welded stainless steel construction with two discharge drillings at an angle of 90°, sheet metal thickness: 2 mm at least / tube Ø 38 mm

Water pipe 0,80 m x 1,60 m
Base area: 0,80 m x 1,60 m
Sheet metal thickness: 2,5 mm
Stainless steel tube Ø 154 mm
Welded stainless steel construction with a sloped feed opening and a sloped run-off, sheet metal thickness: 2 mm at least / tube Ø 154 mm

Water storage basin
Base area: Ø 0,68 m
Welded stainless steel construction with two tubular run-offs. Conical rubber closing with locking mechanism for complete water extraction. Sheet metal thickness: 2 mm at least / tube Ø 33,7 mm.

Water trough type M1 1,60 m, 3 pcs.
Welded stainless steel construction 0,80 m x 1,60 m, Sheet metal thickness: 2 mm at least / tube Ø 38 mm. For post attachment with inclined installation corresponding to water feed or water run-off. Inclined run-off, including flexible flap with stainless steel knob and reinforced rubber blade, clamping device for tube attachment Ø 38 mm

Water wheel
Base area: 0,60 x 0,80 m
Height: 0,90 m
Wheel Ø 0,60 m
Welded stainless steel construction for post attachment, for water collection from a trough on top, 12 paddle wheels, rounded on the front end, framed by side panels. Sheet metal thickness: 2 mm at least. Water wheel mounted in roller bearing.

Water trough type M1 2,40 m
Welded stainless steel construction 0,80 m x 2,40 m, Sheet metal thickness: 2 mm at least / tube Ø 38 mm. For post attachment with inclined installation corresponding to water feed or water run-off. Sloped water run-off

Maxi water table 6 x 0,80 m with discharge lock
Base area: 1,40 x 1,70 m
Height: 0,80 m
Hexagonal stainless steel construction with conical rubber closing for water damming, regulation or redirection. Sheet metal thickness: 2 mm at least.

Water swirl table 0,80 m x 1,60m
Welded stainless steel construction with 5 adjustable triangular HPL plates for water flow obstruction. Sheet metal thickness: 2 mm at least, tube Ø 33,7 mm resp. Ø 30 mm

Metal components: stainless steel
Robinia timber is furnished with water-repellent, breathable protective coating. Besides protection from moisture, that treatment reduces crack formation.

Foundations (on site)
37 pcs. 0,40 x 0,40 x 0,40 m
2 pcs. 0,30 x 0,30 x 0,40 m
concrete amount: 2,5 m³

Approximate assembly values
2 mechanics 10 hours each
(without creating foundations, without water supply connection)

Free height of fall
1,80 m

Appropriate for
children from the age of 5 years up,
public playgrounds etc.,
manual activity