Play Structures

Technical data
Total height: 6,40 m
Area: 9,15 x 15,85 m
Minimum space: 12,35 x 19,30 x 6,40 m (160 m²)
Platform height: 0,20 up to 3,00 m
Slide installation height: 2,00/2,80 m
Slide entrance height: 2,10/2,90 m
Slide inclination: 30°/36°
Slide width: 0,60 m
Thickness of sliding sheet metal: 2,5 mm

Posts
Laminated Robinia timber Ø 120 mm with cylindrical milling. End-grain surfaces are covered by non-detachable protective stainless steel caps. Stainless steel tubular pedestal for concrete-cast foundation and for fixed mounting to round Robinia posts, Ø 120 mm, below playing surface.

Platforms
Platforms from boards of 30 mm thickness and all-round square-shaped joists 45 x 100 mm. Dried timber from Robinia, planed, milled and free from decay. Force-fitting fastening through specific stainless steel brackets with end-to-end bolt assembly.

Attachment parts
– bowed guardrails with roll-off prevention, from stainless steel tubes, Ø 33,7 x 2 mm
– timber infill barriers from Robinia, 125 x 30 mm, fastening between stainless steel tubes Ø 33,7 x 2 mm
– infill panels from highly weather-resistant HPL, fastening between stainless steel tubes Ø 33,7 x 2 mm
– stepped guardrails from stainless steel tubes, Ø 33,7 x 2 mm
– climbing rungs made from stainless steel tubes Ø 33,7 x 2 mm
– cranked ladder rungs made from stainless steel tubes Ø 33,7 x 2 mm
– seats made from highly weather-resistant HPL panel (20 mm thickness)
– tottery bridge suspended from tandem crossbeams, Robinia logs Ø 10 cm, suspended from fine stainless steel chains, protection against the possibility of stepping through
– sloping tottery stairs 0,80 m x 2,40 m, suspended from tandem railings, rungs from Robinia logs Ø 10 cm, fine stainless steel chains
– arch-shaped Robinia bridge
– infill panels (for arch-shaped bridge) from highly weather-resistant HPL, fastening between stainless steel tubes Ø 33,7 x 2 mm
– climb up ramp from highly weather-resistant HPL, 20 mm thickness, stainless steel frame, with five cut-outs for climbing
– climbing net from stainless steel chains, suspended from stainless steel crossbeam
– suspension bridge from Robinia joists 45 x 100 mm with rubber buffers 30 mm, stainless steel supporting cable Ø 10 mm with four tensioning devices, fine stainless steel chains
– plank bridge: V-shaped climbing net construction from Hercules ropes, Robinia footbridge with approx. 40 mm clear distance between the planks. Attachment to a steel frame construction. Barrier height approx. 0,75 m
– stainless steel support posts for a bridge Ø 120 mm
– inclined Robinia ramp with stainless steel tandem guardrail and pre-assembled Hercules rope
– climbing wall with 6 cut-outs from highly weather-resistant HPL, 20 mm thickness, framed by stainless steel tubes
– vertical handle from stainless steel tube Ø 33,7 x 2 mm, as a climbing aid
– climbing pole from tubular stainless steel Ø 38 mm with horizontal arch
– attachment slide, width 0,60 m, one-piece welded assembly with roll-off prevention, sheet metal thickness 2,5 mm, with additional support beneath run-out section. Slide of low noise level thanks to trough-shaping
– tower roof, inclination 80°, made from highly weather-resistant HPL, 13 mm thickness, with whirligig
– hill slide 30°, installation height 2,80 m, stainless steel sliding segments, of low noise level thanks to trough-shaping, one-piece welded assembly, including stainless steel support post for the curved section and fastening flange

For your planning, due to a possible sliding surface heating, please see to a north-east orientation of the slides or provide half-shade of trees.

Metal components: stainless steel

Robinia timber is furnished with water-repellent, breathable protective coating. Besides protection from moisture, that treatment reduces crack formation. Thanks to a specific fastening adaptor, forces arising from the modular attachment parts are directly derived into the posts. Tamper-proof connections thanks to screws with protective screw caps.

Foundations (on site)
34 pcs. 0,40 x 0,40 x 0,40 m
1 pc. 0,40 x 0,75 x 0,40 m
1 pc. 1,40 x 0,75 x 0,40 m
7 pcs. 0,30 x 0,30 x 0,40 m
2 pcs. 0,60 x 1,00 x 0,50 m
1 pc. 0,40 x 0,40 x 0,60 m
concrete amount: 3,66 m³

Approximate assembly values
4 mechanics 15 hours each
(without creating foundations)

Free height of fall
2,90 m

Appropriate for
children from the age of 4 years up,
public playgrounds etc.,
physical activity